維卡軟化點測試的簡單介紹

維卡軟化點測試的詳細信息

安裝與操作說明：

試驗前的準備工作。 根據試驗類型選擇試驗壓頭，熱變形為圓角壓頭，維卡為針型壓頭。將所需的壓頭與負載桿固定好。 根據試驗類型和試樣的尺寸計算載荷： a、熱變形試驗：根據試樣的尺寸，選取載荷b、維卡試驗：只有兩種規定的負荷A法9.81N 即1000g B法 49.05N即5000g 砝碼的選配見（9）砝碼質量表 打開攪拌電機電源，指示燈亮，攪拌電機工作，攪拌速度可以通過攪拌電機控制盒上的旋鈕調節（溫度高時用慢速，溫度低時用快速），按照以上指定的程序檢查電氣，無誤后繼續做下面的工作。維卡軟化點測試 安裝試樣 將試樣架抬（升）出油面，將熱變形試樣放在支撐架上（維卡試樣放在平面上），放下負載桿，將試樣壓緊。 將試樣架放（降）回油池內，將相應質量的砝碼放在托盤上。要求砝碼放正。 將千分表固定在砝碼上方，使千分表內芯懸于砝碼之上，內芯上端有2-5mm的空間。 升溫速率設定：共有兩檔升溫速率，120℃/h，50℃/h。 每次試驗時需要對千分表進行調零，方可進行試驗，調零時輕輕旋動旋鈕，使千分表置于零區，預置3-5分鐘。 啟動工作：當一切準備工作就緒后，試驗開始。 試驗結束，記錄下溫度；移開千分表及砝碼，抬（升）起試驗架，取下試樣。注意不要把試樣誤入油池。 降溫采用氣冷或水冷，也可自然冷卻。維卡軟化點測試冷卻時，可抬起或?qū)⒃嚇蛹軡撊胗统亍?/span> 關閉主機電源、攪拌電機電源。

維卡軟化點測試主要配置：

1.試驗主機一臺 　

2.溫度傳感器一只 　

3.光柵千分表三塊 　

4.熱變形及維卡測頭各三套

5. 打印機一臺

6. 專用工具一套

維卡軟化點測試維卡技術參數：

1、溫度控制范圍：環境溫度——300℃

2、升溫速率：120±5℃/h(12±1℃/6min)或50±3℃/h(5±0.5℃/6min)

3、溫度分辨率：0.01℃ 3、最大溫度誤差：±0.5℃

4、形變測量方法：千分表 5、變形測量范圍：-0.1mm——5.0mm

6、最大變形誤差：±0.01毫米

7、試 樣 架 數：三架一溫

8、加 熱 介 質：甲基硅油(需方自備)

9、加 熱 功 率：2.5KW

10、冷 卻 方 法：150℃以上自然冷卻，150℃以下自然冷卻或水冷

11、具有上限溫度任意設定(環境溫度——300℃)的保護功能或最高上限300℃的保護

12、負載桿和壓頭總質量：88g

13、試驗最大負荷：

A：維卡試驗負荷：GA=10N±0.2N(即1000g)、 GB=50N±1N(即5000g)

B：熱變形試驗負荷：F=2×δ×b×h×h/(3×L) 式中：F——試樣所需加的載荷，單位N δ——熱變形標準彎曲正應力：

維卡軟化點測試方法

A：使用纖維應力1.80MPa 方法

B：使用纖維應力0.45MPa

方法C：使用纖維應力8.00MPa b——試樣的寬度，單位m h——試樣的高度，單位m L——兩支點間的距離，0.100m 14、電 源：AC220V±10%、50Hz、30A 15、需方自備甲基硅油：閃點300度、粘度200厘斯，20升。

Installation and operating instructions:

The preparing work before test. Select test head depending on the type of test, the thermal deformation for the rounded head, d card type for the needle head. The required pressure head and load rod fixed well. And depending on the type of test sample size calculation load: a, thermal deformation test: according to the size of the sample, select load b and d card test: there are only two rules of load a method b method 49.05 N 9.81 N or 1000 g or 5000 g weight matching (9) see farmar quality table Open the mixing motor power, indicator, mixing motor work, stirring speed can be regulated by mixing motor control knob on the box (at high temperature with slow, at low temperature with quick), in accordance with the procedures specified above check electric, and continue to do the following work. Vicat softening point test sample carried the specimen holder installation (l) the oil level, the thermal deformation of specimen on the supporting frame (d card samples on the plane), put down the load bar, the sample pressure. Put (down) to the specimen holder oil pool, the corresponding weight of quality on the tray. Asked farmar is. Add dial gauge fixed above the weight, the dial gauge will hang on the weights, the upper inner core with 2-5 mm space. Heating rate setting: a total of two heating rate, 120 ℃ / h, 50 ℃ / h. The dial indicator to zero in each test before experiment, the zero gently turn knob, make the dial indicator at zero, preset for 3 to 5 minutes. Start work: after all preparations were made, trial begins. End of the test, record the temperature; Remove the dial indicator and Jordan farmar, lift (l) test machine, remove the sample. Be careful not to put the sample into the oil pool. Cooling the air cooled or water cooling, natural cooling. Vicat softening point test is cooling, the sample can be raised or frame into oil pool. Shut down the host power supply, mixing motor power.

Vicat softening point test main configuration:

1. The test host

2. A temperature sensor

3. The grating dial gauge three pieces

4. The thermal deformation and three sets of vicat probe

5. A printer

6. Special tools

Vicat softening point test d card technology parameters:

1, the range of temperature control: the environment temperature - 300 ℃

2, the heating rate: 120 + 5 ℃ / h (12 + / - 1 ℃ / 6 min) or 50 + 3 ℃ / h (5 + / - 0.5 ℃ / 6 min)

3, temperature resolution: 0.01 3 ℃, the maximum error of the temperature: plus or minus 0.5 ℃

4, deformation measurement methods: dial gauge, deformation measurement range: 5-0.1 mm - 5.0 mm

6, the maximum deformation error: + / - 0.01 mm

7, try sample number: three temperature

8, add heat medium quality: silicone fluid (the buyer should bring along their own)

9, add heat power: 2.5 KW

10, but cold method: 150 ℃ above natural cooling, natural cooling or water cooling under 150 ℃

11, has the limit temperature set arbitrary (ambient temperature - 300 ℃) of protection or the protection of the top limit of 300 ℃

12, rod load and pressure head total quality: 88 g

13, maximum load test:

A: d card test load: GA = 10 N + / - 0.2 N (1000 g), GB = 50 N + 1 N (5000 g)

B: hot deformation test load: F = 2 x delta * * h * h/B (3 x L) : F - sample needed to add load, unit N delta - hot deformation standard bending normal stress:

Vicat softening point test method

A: the use of fiber stress 1.80 MPa method

B: the use of fiber stress 0.45 MPa

C: the use of fiber stress 8.00 MPa, the width of the sample b, unit m h, the height of the sample, the unit m L, the distance between the two fulcrum, 0.100 m (14, electricity source: AC220V plus or minus 10%, 50 hz, 15, the buyer should bring along their own methyl silicone oil, 30 a flash point 300 degrees, the viscosity of 200 CST, 20 liters.

以上是維卡軟化點測試的詳細信息，如果您對維卡軟化點測試的價格、廠家、型號、圖片有任何疑問，請聯系我們獲取維卡軟化點測試的最新信息